Car Welding for Croydon Drivers: MOT Corrosion Repairs Done Properly

Croydon drivers cover a lot of hard, stop-start miles, and high-mileage cars often reach the point where the MOT fails them on corrosion rather than anything mechanical. We're about 15 minutes from Croydon in Hackbridge, and we repair structural rust with new steel, not filler.

  • ★★★★★ 4.9/5 from 193 Google reviews
  • ~15 min from Croydon
  • Mon–Fri 8am–8pm · Sat 8am–5pm
Car raised on the ramp for underbody inspection at KITH Cars Garage & Bodyworks, Hackbridge

High-mileage Croydon cars and the MOT corrosion failure

Between the commuting, the school runs and the private-hire and delivery work that keeps the town centre moving, a lot of Croydon cars rack up big mileages. A car that spends its day on London Road and Brighton Road, or circling past Fairfield Halls and No. 1 Croydon, can have a perfectly healthy engine at 150,000 miles. What often ends its working life is rust in the sills, floor or rear subframe mounts, spotted at the MOT. For a working car, a fail means lost earnings, so a quick, proper repair matters.

Heavy use speeds rust up in a few ways. Cars that work through the winter carry salty spray underneath every day and rarely get washed underneath. Jacking points on high-mileage cars have usually been jacked on many times for tyres and repairs, and a crushed jacking point lets water straight into the sill. That's why we check those areas as a matter of routine. Stop-start traffic through the Lombard and Fiveways junctions also means lots of short journeys between long waits, and the underside rarely gets properly dry.

The repair itself is the same careful job whatever the car does for a living. We cut back to clean steel, weld in new metal and seam seal, prime and coat it, with cavity wax inside any enclosed section. If you need the car back quickly, tell us when you book. A single MOT repair can often be done in a few hours, and you'll have a written quote before we start. If it's a working car, we can also look for other weak spots so you're not back for another fail a month later.

Getting to us from Broad Green or the centre is straightforward via the Flyover and the A232, which also keeps you clear of the borough's Healthy Neighbourhood camera filters, where through traffic without a permit is fined. If the MOT has rated the corrosion as dangerous, don't drive it; we can collect it. Repairs carry our 12-month workmanship warranty.

Welding & Rust Repair: what’s involved

Most cars have a monocoque body, meaning the shell itself acts as the chassis. Sills, floor pans, crossmembers and the areas around suspension and seat belt mountings carry load, so rust there weakens the car. Corrosion usually starts where water and road salt collect: inside sills, behind arch liners, along seams and around jacking points, and it often works from the inside out.

The MOT treats corrosion seriously. Excessive corrosion in load-bearing structure is a failure, particularly within 30cm of prescribed areas such as suspension, steering and seat belt mounting points. A proper repair means cutting back to sound metal, fitting a new steel section and welding it in, then sealing and protecting it inside and out. Covering rust with filler or a plate over rotten metal doesn't fix it, and a tester can fail an inadequate repair on a structural area.

From £80Written quote first
2 hours – 3 daysTypical time in the workshop
3 monthsWorkmanship warranty
4.9★193 Google reviews

Signs of rust that needs welding

Bubbling paint on sills or arches

Rust forming underneath the paint. It's usually more extensive than the visible bubbles suggest.

Holes or flaking metal underneath

Floor pans, sills, jacking points and crossmembers that flake or can be pushed through with a probe.

MOT advisory or failure for corrosion

An advisory is a warning worth acting on; a failure for structural corrosion must be repaired before the car can pass.

Soft or crumbling jacking points

If the sill crushes or the jack sinks into it, the structure around it is weakened.

Rust around suspension mountings

Corrosion near spring seats, strut tops, subframe or trailing arm mounts is structural and needs prompt repair.

Water in the footwells

Can be caused by holes in the floor, although blocked drains and door seals are more common causes, so we check.

Rust on door bottoms and boot floor

Often cosmetic rather than structural, but cheapest to repair while the rusted area is still small.

When should it be done?

Deal with structural rust as soon as it's found, ideally before the MOT so you have time to plan. Corrosion advisories are worth acting on, because another winter of salted roads can turn an advisory into a failure needing bigger repairs. Cosmetic rust on door bottoms or arch edges isn't a safety issue, but it's cheapest to fix while it's still at the bubbling stage. Older and classic cars benefit from a regular underside inspection.

  • MOT advisory mentioning corrosion: before the next winter or MOT
  • MOT failure for corrosion: before retest, and before driving at all if the defect was rated dangerous
  • Bubbling paint on sills, arches or door bottoms: while the rust is still small
  • Buying an older or classic car: underside inspection before or soon after purchase

How we repair rust and welding

  1. Inspection on the rampWe examine the underside, probe suspect areas and read any MOT failure sheet, separating structural corrosion from cosmetic.
  2. Written quoteWe explain what's structural, what's cosmetic and what should be prioritised. Rust sometimes proves more extensive once cut into, and we'll contact you before doing anything extra.
  3. Access and protectionTrim, arch liners, seats or carpets are removed as needed, and fuel lines, brake pipes and wiring are protected or moved away from heat.
  4. Cut out corrosionRusted metal is cut back until we reach clean, sound steel.
  5. Fabricate or fit repair sectionsNew steel sections are formed in the workshop, or pre-formed repair panels are used where available and a good fit.
  6. Weld inThe new metal is MIG welded in, seam welded where the structure requires it, and the welds are dressed back.
  7. Seal and protectJoints are seam sealed and primed, the underside is coated with underbody protection and enclosed sections are treated with cavity wax.
  8. Refit, check and hand overEverything is refitted, pipes and wiring are checked, and we explain what was repaired and anything else worth watching.

Steel and materials

Repairs are made with new steel of a suitable thickness for the area, either fabricated in the workshop or using pre-formed repair panels where they're available and fit well. After welding, joints are sealed, primed and protected with underbody coating, and enclosed sections such as sills are treated with cavity wax, which creeps into seams to slow future corrosion from the inside.

  • New steel sheet of the appropriate thickness
  • Pre-formed sill and arch repair panels where suitable
  • Weld-through primer and anti-corrosion primer
  • Seam sealer
  • Underbody protection and cavity wax

How long it takes

2 hours – 3 days

A single small MOT repair can often be done in 2–4 hours. Sills, floor sections or several areas can take 1–3 days, and extensive work on older cars longer. If the rust turns out to be worse once cut out, we'll call you before going further.

What’s included

  • Underside inspection and written quote
  • Cutting out corrosion back to sound metal
  • New steel welded in
  • Seam sealing, priming and underbody protection on the repair
  • Cavity wax in enclosed sections that have been repaired
  • 12-month workmanship warranty

From Croydon to our Hackbridge workshop

From the town centre take the Croydon Flyover (A232) west onto Duppas Hill Road and Epsom Road to the Fiveways junction with Purley Way (A23). Continue on Croydon Road (A232) through Waddon and Beddington, past Beddington Park, to the junction with Manor Road and London Road in Wallington, then turn right onto London Road (A237) and head north to Hackbridge; Soho Mills is on the right.

Take the Croydon Flyover (A232) west to Fiveways, then carry on along Croydon Road through Waddon and Beddington to Wallington and turn right up London Road (A237), around 15 minutes. Cars with a dangerous defect can be collected from Croydon.

Directions from Croydon

About Croydon

Croydon is one of the largest commercial centres in Greater London: a dense town centre of office towers, flats and shopping around East and West Croydon stations, ringed by Victorian and Edwardian terraces and leafier inter-war suburbs such as Addiscombe, Shirley and South Croydon. It is a busy place with a large commuting population thanks to fast trains to London Bridge and Victoria. Driving through the centre means multi-lane gyratories, the Croydon Flyover and Underpass, tram tracks and heavy traffic on the A23 and A232 corridors, while the side streets are mostly 20mph and tightly parked.

Places nearby: East Croydon station, Boxpark Croydon, Croydon Minster, Whitgift Almshouses, Fairfield Halls, No. 1 Croydon

Postcodes: CR0, CR2, CR9 · London Borough of Croydon

More about KITH for Croydon drivers

Welding & Rust Repair in Croydon: your questions answered

My private-hire car failed its MOT on corrosion. How fast can you fix it?

A single small repair is often done in 2–4 hours, and larger sill or floor work can take a day or more. We'll give you a realistic timescale with the written quote. Book early in the day if you can, so we can aim to finish the same day.

Is it worth welding a car with very high mileage?

Mileage matters less than overall condition. If the engine, gearbox and suspension are in good order and the rust is confined to a few areas, a welding repair is usually good value. If corrosion is widespread, we'll say so.

How do I avoid Croydon's traffic filters on the way to you?

The main route via the Croydon Flyover, the A232 through Waddon and Beddington, then London Road in Wallington, uses main roads rather than the filtered residential streets. Following the A-roads the whole way keeps it simple.

Will my car pass the MOT after welding?

We repair the items on your failure sheet to a standard that meets the MOT inspection requirements, although the tester makes the final decision at the retest. If we find other corrosion nearby that's likely to cause a problem, we'll point it out before the retest.

Is it worth welding an older car?

It depends on how much rust there is and what the car is worth. A couple of sill repairs on an otherwise sound car are usually worthwhile. Widespread corrosion across floors, sills and mountings can cost more than the car is worth, and we'll give you an honest view.

Can you just patch over the rust?

Not on structural areas. Welding a plate over rotten metal traps moisture so the rust carries on underneath, and a tester can fail it as an inadequate repair. We cut out to sound metal and weld in new steel.

What's the difference between structural and cosmetic rust?

Structural rust affects load-bearing parts such as sills, floors, crossmembers, chassis legs and the areas around suspension and seat belt mountings. Cosmetic rust is on outer panels like door skins and bolt-on wings, which aren't load-bearing and usually only fail an MOT if they leave sharp edges.

How can I slow down rust?

Rinse the underside during winter to remove road salt, keep door and sill drain holes clear, and deal with stone chips early. On older cars, cavity wax in the sills and underbody protection make a real difference, and we can apply them.

Price your welding and rust repair now

Enter your reg and we’ll look up your car and price the job from our own labour rates and the book time for your model. Then book it in with a fixed written quote before any work starts.

  • Free, about 30 seconds, no sign-up
  • Parts, labour and VAT included
  • 12-month workmanship warranty
  • Collection from Croydon can be arranged
“It’s rare to find a garage you can truly trust. Fair price, brilliant customer service.”Thinushan K. · ★★★★★ Google

Prefer to talk? Call 020 4629 9469 or WhatsApp us.

Loading instant quote…
Chat on WhatsApp